GSC Power-Division Camshafts & Valvetrain

GSC Powe Division billet 7008S2 cams for the Mitsubishi Evo 4-8 are designed for those with a goal of 400-700 WHP. No low end power is lost vs. the stock cams when used with the larger turbos. The S2 cams will show gains of 50-70 WHP over the stock cams, and in some cases more in the higher RPMs.GSC Power Division Evolution S2 Camshafts  Great for 2.0L engines with stock frame turbos revving to 9000 RPMs or for stroker motors revving to 8000 RPMs. The S2 cams are suggested to run on our upgraded beehive valve spring replacement or full beehive valve spring kit with Titanium retainer. GSC Power Division Evolution S2 Camshafts

• Designed for a rev range of 4000-9000 RPMs (2.0L or 3000-8000 2.2L+)
• S2 cams can run on Factory ECU with custom flashing
• Made 100% in the USA

**If using aftermarket cam gears (especially AEM) check the bolt length. Some cam gears are too thick for the OEM bolt on the billet cams, a 40mm underhead length bolt may be necessary in this case**

GSC Power-Division billet S3 cams for the Evo 4-8 4G63 are meant for 800+ WHP to take advantage of a very large turbo. These are NOT suggested for anyone running smaller than the 67mm to GT42R turbo.

**If using aftermarket cam gears (especially AEM) check the bolt length. Some cam gears are too thick for the OEM bolt on the billet cams, a 40mm underhead length bolt may be necessary in this case**

GSC Power-Division billet S1 cams for the Mistubishi Evo 9 are designed for those with a stock turbo all the way to a GT30/50 trim. These cams will not sacrifice any bottom end loss over stock cams; nothing but gains, and will promote faster spooling of the upgraded turbos. Gains of 25-40 WHP (depending on turbo) have been seen by simply bolting the S1 cams in. GSC Power Division Mivec S1 Camshafts

• Designed for a rev range of 3000-8000 RPMs
• These cams work well on the stock valve springs
• 300-450 WHP camshaft
• Made 100% in the USA

**If using aftermarket cam gears (especially AEM) check the bolt length. Some cam gears are too thick for the OEM bolt on the billet cams, a 40mm underhead length bolt may be necessary in this case** GSC Power Division Mivec S1 Camshafts

GSC Power-Division billet 7009S2 cams for the Mitsubishi Evo 9 are designed for those with a goal of 400-700 WHP. No low end power is lost vs. the stock cams when used with the larger turbos. The S2 cams will show gains of 50-70 WHP over the stock cams, and in some cases more in the higher RPMs. Great for 2.0L engines with stock frame turbos revving to 9000 RPMs or for stroker motors revving to 8000 RPMs. GSC Power Division 9 Mivec Camshafts The S2 cams are suggested to run on our upgraded beehive valve spring replacement or can be run at the stock revlimit and factory boost on the stock spring.

• Designed for a rev range of 4000-9000 RPMs (2.0L or 3000-8000 2.2L+)
• 400-700 WHP applications
• S2 cams can run on Factory ECU with custom flashing
• Made 100% in the USA

**If using aftermarket cam gears (especially AEM) check the bolt length. Some cam gears are too thick for the OEM bolt on the billet cams, a 40mm underhead length bolt may be necessary in this case**

GSC Power-Division billet 7009S3 cams are a hydraulic lifter profile for the Evo 9 4G63. These cams are meant for 700+ WHP to take advantage of a very large turbo. These are NOT suggested for anyone running smaller. GSC Power Division S3 Camshafts 4G63

GSC Power Division Billet R2 Cams The billet 7009R2 is a high lift, very aggressive profile with a short overall duration to keep a lower usable RPM band. The 7009R2 is designed to rev between 4000-8500 RPMs and should be used with a stroked engine or added displacement engine. The peak lift of 12.10mm intake and 12.00mm exhaust will require upgraded valve springs and a titanium retainer with special attention to seal to retainer clearance. With the lift of this profile, it is suggested to only use the 5041/5040 Ti retainer and spring kits due to valve seal to retainer clearance. The 5041 can be used to 40+psi and the 5040 to 32psi on the R2 profile at 8500 RPMs without float or flutter issues. The profile will work fine on the OEM rocker arm and the zero-tick lifter or with the OEM lifter. We have seen gains of 25-30 WHP over the S2 profile on the stroked applications, with much more possible when used with a ported head and aftermarket intake manifold. GSC Power Division Billet R2 Camshafts

**If using aftermarket cam gears (especially AEM) check the bolt length. Some cam gears are too thick for the OEM bolt on the billet cams, a 40mm underhead length bolt may be necessary in this case**

GSC Power-Division billet S1 cams for the Mitsubishi Evo X are designed for those with the stock turbo up to the 550 HP range. These cams will not sacrifice any bottom end loss over stock cams; nothing but gains, and will promote faster spooling of the upgraded turbos. Gains of 20-50 WHP (depending on turbo) have been seen by simply bolting the S1 cams in. 

• Designed for a rev range of 3000-7500 RPMs
• The S1 cams work well on the stock valve springs
• Forged billet core
• Made 100% in the USA

GSC Power-Division billet S2 cams for the Mitsubishi Evo X are designed for those with 600+ HP in mind. Gains of 40-80 WHP (depending on turbo) have been seen by simply bolting the S2 cams in.

• Designed for a rev range of 3800-8500 RPMs
• The S2 cams require an upgraded valve spring
• Forged billet core
• Made 100% in the USA

GSC Power-Division billet S1 cams for the Hyundai G4KF Theta are designed for those with the stock turbo up to the 550 HP range These cams will not sacrifice any bottom end loss over stock cams; nothing but gains, and will promote faster spooling of the upgraded turbos. Gains of 20-50 WHP (depending on turbo) have been seen by simply bolting the S1 cams in.

• Designed for a rev range of 3000-7500 RPMs
• The S1 cams work on the stock valve springs, but its suggested to upgrade
• Forged billet core
• May require head clearancing - check on install

GSC Power-Division S2 billet cams for the Hyundai G4KF Theta are designed for those with 600-800 HP in mind. Gains of 40-60 HP (depending on turbo) have been seen by simply bolting the S2 cams in.

• Designed for a rev range of 3800-8000 RPMs
• The S2 cams require an upgraded valve spring.
• Forged billet core
• Head clearancing required

The GSC Power Division G4KF S3 Camshafts cams for the Hyundai G4KF Theta are designed for those with 800+ HP in mind.

• Designed for a rev range of 4500-9500 RPMs
• The S3 cams require an upgraded valve spring - GSC5062 recommended.
• Forged billet core
• Head clearancing required 

GSC Power-Division billet S1 Cams for the Gen 2 3SGTE MR2 Turbo, with shim over bucket design. Designed for turbo upgraded 3SGTEs running between 300-450 WHP.

• GSC 3SGTE Intake cams have the pin relief to run the 4th gen trigger and a M10X1.25 set screw. You will be required to remove the M10X1.25 set screw so that you can run the 4th gen trigger and factory trigger bolt.

GSC Power-Division billet S2 Cams for the Gen 2 3SGTE MR2 Turbo, with shim over bucket design. Designed for upgraded turbo, ported cylinder head, built engine with ECU tuning. 500-600 WHP.

• GSC 3SGTE Intake cams have the pin relief to run the 4th gen trigger and a M10X1.25 set screw. You will be required to remove the M10X1.25 set screw so that you can run the 4th gen trigger and factory trigger bolt.

GSC Power-Division billet S1 Cams for the Gen 3 3SGTE MR2 Turbo, with shim under bucket design. Designed for turbo upgraded 3SGTEs running between 300-500 WHP. These cams give you faster spool, with more mid range, while still being able to rev out to 8000 RPM.

• GSC 3SGTE Intake cams have the pin relief to run the 4th gen trigger and a M10X1.25 set screw. You will be required to remove the M10X1.25 set screw so that you can run the 4th gen trigger and factory trigger bolt.

GSC Power-Division billet S2 Cams for the Gen 3 3SGTE MR2 Turbo, with shim under bucket valve train. Designed to support over 850 WHP. This cam is for a serious engine: big turbo, built motor, built/ported head, and engine management. You will notice better spool characteristics, and more horsepower and torque in the mid and top end of the revs.

• GSC 3SGTE Intake cams have the pin relief to run the 4th gen trigger and a M10X1.25 set screw. You will be required to remove the M10X1.25 set screw so that you can run the 4th gen trigger and factory trigger bolt.

GSC Power-Division billet S3 Cams for the Gen 3 3SGTE MR2 Turbo, with shim under bucket valve train. Designed to support 850+ WHP with high revs. This cam is for a serious engine: big turbo, built motor, built/ported head, and engine management.

• GSC 3SGTE Intake cams have the pin relief to run the 4th gen trigger and a M10X1.25 set screw. You will be required to remove the M10X1.25 set screw so that you can run the 4th gen trigger and factory trigger bolt.

GSC Power-Division Billet R1 camshaft set for Nissan RB26DETT GSC Power Division R1 camshaft Nissan 

*Reduced base circle = 30.5mm

GSC Power-Division Billet R2 camshaft set for Nissan RB26DETT GSC Power Division R2 camshaft Nissan

*Reduced base circle = 30mm

GSC Power-Division Billet S1 camshaft set for Nissan VR38DETT GT-R

GSC Power-Division Billet S2 camshafts for the Subaru EJ207 version 7 and above with single AVCS. These cams are built to suit higher horsepower engine builds with a power range of 500 WHP and above.  Certain modifications are recommended to utilize the true potential of the S2's including an upgraded engine block, built/ported heads, and dyno engine tuning. Upgraded valve springs are required.  Due to the added lift and duration, cylinder head clearancing may be required.

• Check cylinder head for lobe clearancing.  

GSC Power-Division Billet S2 camshaft set for Nissan RB26DETT 

GSC Power Division is glad to reveal the newest addition to our camshaft line, the GSC7045 forged billet S2 set for the VR38 powered GT-R. This isn’t just another cam - lots of research and development went into every aspect of these bump sticks. The billet cores for these cams are proprietary and made in house at GSC. We developed stronger, lighter cams with additional fatigue and wear resistance. CNC machining and grinding gives us the most accurate and repeatable camshafts possible, with precision gun drilling down the center of the cam for oil delivery and weight reduction. This far exceeds OEM durability with the performance GSC Power-Division is world famous for. Good for mild builds all the way up to 1500+ HP strokers. GSC Power Division camshaft Nissan VR38DETT

Required for the 7045S2 cams are the GSC5068 Conical valve springs and lightweight titanium retainers. These will keep the valve train happy up to 9800 RPM at 60psi of boost. GSC specifically designed the valve springs and retainers for the high horsepower VR38DETT and utilize different intake and exhaust retainers to keep proper spring seat pressure.

• Head Clearancing may be necessary for lobes 
• Intake: Valve Clearance = 0.30mm±0.025mm
• Exhaust: Valve Clearance = 0.33mm±0.025mm

GSC Power-Division is glad to reveal the newest addition to our camshaft line, the GSC7045 forged billet S3 set for the VR38 powered GT-R. This isn’t just another cam - lots of research and development went into every aspect of these bump sticks. The billet cores for these cams are proprietary and made in house at GSC. We developed stronger, lighter cams with additional fatigue and wear resistance. CNC machining and grinding gives us the most accurate and repeatable camshafts possible, with precision gun drilling down the center of the cam for oil delivery and weight reduction. This far exceeds OEM durability with the performance GSC Power-Division is world famous for. For 1500 + WHP builds only. GSC Power Division S3 camshaft VR38DETT

Required for the 7045S3 are the GSC5068 Beehive valve springs and lightweight titanium retainers, this combination will keep the valve train happy up to 9800 RPM at 60psi of boost. GSC specifically designed the valve springs and retainers for the high horsepower VR38DETT and utilize different intake and exhaust retainers to keep proper spring seat pressure.

• Suggested for stroker or high revving engines
• Head clearancing may be necessary for lobes

GSC Power-Division Billet S4 camshaft set for Nissan VR38DETT GT-R

GSC Power Division S4 camshaft VR38DETT 

GSC Power-Division Billet S4M camshaft set for Nissan VR38DETT GT-R for those running methanol 

GSC Power-Division billet T1 cams for the VQ35DE.